(1)T.Sakoda, M.Otsubo, C.Honda and H.Nieda: "Gas Temperature and Cu
Vapor Density in an Impulse Discharge ", Trans.IEE of Jpn., Vol.116-A,
N0.11 (1996.11)
(2)T.Sakoda, H.Iwamiya, K.Uchino, K.Muraoka, M.Itoh and T. Uchida: "Electron Temperature and Density Profiles in a Neutral Loop Discharge Plasma" Jpn.J.Appl.Phys., Vol.36, part2, No.1A/B, pp.L67-L69 (1997.1)
(3)T.Sakoda,T.Miyao K.Uchino and K.Muraoka: "Studies of a Magnetic Neutral Loop Discharge Based on Laser Diagnostics of Electron Behavior and Atomic Processes " Jpn.J.Appl.Phys., Vol.36, No.11, pp6981-6985 (1997.9)
(4)T.Sakoda, T.Arita, H.Nieda, K.Ando, M.Otsubo and C. Honda: "Studies of Elastic Waves Caused by Corona Discharge in Oil", IEEE Trans. on Dielectrics and E.I, Vol.6, pp825-830 (1999.12)
(5)迫田達也, 贄田寛, 安藤喜代美 :"弾性波による変圧器絶縁油の絶縁劣化診断技術",電学論A, Vol. 120-A, No.5, pp601-606 (2000.5)
(6)T.Sakoda, H.Nieda, K.Kitahara and K.Ando: "Studies of the reaction difference between γ-ray and glow discharge on hydrogenation", Radioisotopes, Vol.49, No.8, pp393-397 (2000.8)
(7)深野孝人,堀口友隆,大坪昌久,本田親久,迫田達也,贄田寛:"直列ギャップ付避雷器の漏れ電流へのスペーサ表面の金属汚損の影響",電気設備学会, Vol.20, No.10, pp828-834 (2000.10)
(8)Y.M.Sung, K.Uchino, K.Muraoka and T.Sakoda: " Studies on the optimum condition for the formation of a neutral loop discharge plasma ", J.Vac.Sci.Technol.A, Vol.18, No.5, pp2149-2152 (2000.10)
(9)T.Sakoda, H.Nieda and K.Ando, " Diagnostics of transformer oil by elastic waves", Electrical Engineering in Japan, Vol. 135, No. 1, pp1-7 (2001.2)
(10)T.Sakoda, H.Nieda and K.Ando: " Characteristics of Elastic Eaves Caused by Corona Discharges in an Oil Immersed Pole Transformer", IEEE Trans. on Dielectrics and E.I, Vol.8, No.2, pp276-283 (2001.4)
(11)Y.O.Yirenkyi, Y.M.Sung, M.Otsubo, C.Honda and T.Sakoda: "Experimental and Numerical Analyses of Electron Temperature and Density Distribution in a Magnetic Neutral Loop Discharge Plasma", Journal of Vacuum Science and Technology A, Vol. 19, No. 2, pp. 2590-2595 (2001.9)
(12)T.Sakoda, Y.O.Yirenkyi, Y.M.Sung, M.Otsubo and C.Honda: "Investigation of the Condition Required for the Formation of a Magnetic Neutral Loop Discharge Plasma", Jpn.J.Appl.Phys. Vol. 40, No. 11, pp 6607- 6612 (2001. 11)
(13)Y.O.Yirenkyi, Y.M.Sung, M.Otsubo, C.Honda and T.Sakoda: " Two-dimensional Modeling and Optimization of a Neutral Loop Discharge Etcher in an Argon Plasma", Elsevier Science in Surface and Coatings Technology, Vol. 149, pp.185-191 (2002.1)
(14)T.Sakoda, S.Maeda, K.Nishihara and K.Furukawa:" Surface Treatment of Powdery Silica Gel Using a Dielectric Barrier Discharge", Trans. of the Materials Research Society of Japan, Vol.27, No.3, pp483-486 (2002.9)
(15)T.Sakoda, Y.M.Sung: "Studies on electron behaviors at downstream region of a neutral loop discharge plasma", Journal of Vacuum Science and Technology A, Vol. 20, No. 6, pp. 1964-1968 (2002. 11)
(16)Y.M. Sung , M.Otsubo, C.Honda and T.Sakoda : " Observation of Copper Atoms Behavior in a Vacuum Arc Discharge using Laser Spectroscopy", Journal of Vacuum Science and Technology A, Vol. 21, No. 1, pp. 180-185 (2003.1)
(17)Y.M.Sung and T.Sakoda :"Spatial Distribution of Charged Particles in a Magnetic Neutral Loop Discharge Etcher", Elsevier Science in Surface and Coatings Technology, Vol. 166, pp.135-140 (2003.1)
(18) T. Sakoda, K. Imagawa and K. Furukawa : "Surface Modification of Molding Silica Gel Using Dielectric Barrier Discharge", Trans. of the Materials Research Society of Japan, Vol.28, No.2, pp209-213 (2003.7)
(19) Tatsuya Sakoda and Yoshito Sonoda : "Transmission and Detection of Light Diffraction Signal by Low-Frequency Ultrasonic Wave" ,Jpn. J. Appl. Phys. Vol. 42, No. 9A, pp 5281- 5285 (2003. 9)
(20) M. Otsubo, T. Hashiguchi, C. Honda, O. Takenouchi, T. Sakoda and Y. Hashimoto: "Evaluation of Insulation Performance on Polymeric Surface by a Novel Separation Technique of Leakage Current", IEEE Trans. on DEI, Vol. 10, No. 6, pp.1053-1060 (2003. 10)
(21) T. Sakoda, K. Matsukuma, I. Araki, Y. M. Sung and K. Furukawa: " Activation of Electrode Surface on Silicon Solar Cell using Dielectric Barrier Discharge", Jpn. J. Appl. Phys. Vol. 43, No. 6A, pp 3275- 3280 (2004. 6)
(22) T. Sakoda and Y. M. Sung : " Dependence of Ozone Generation in a Micro Dielectric Barrier Discharge on Dielectric material and Micro Gap Length", KIEE International Transactions on EA, Vol. 4-C, No. 5, pp201-206, (2004. 11)
(23) T. Sakoda, K. Matsukuma, Y. M. Sung, H. Otsubo, M. Tahara and Y. Nakashima: "Additional Plasma Surface Texturing for Single Crystalline Silicon Solar Cells Using Dielectric Barrier Discharge", Jpn. J. Appl. Phys. Vol. 44, No. 4A, pp 1730- 1731 (2005. 4)
(24)Y. M. Sung and T. Sakoda: "Optimum conditions for ozone formation in a micro dielectric barrier discharge", Surface & Coating Technology, Vol. 197, pp. 148-153 (2005. 7)
(25) T. Sakoda, T. Hamada and K. Matsukuma: " Plasma Surface Texturing of Single-Crystal Silicon Using Dielectric Barrier Discharge", Trans. of the Materials Research Society of Japan, Vol. 30, No.3, pp.595-598 (2005. 9)
(26) T. Sakoda and Y. Sonoda : " Measurement of Low-Frequency Ultrasonic Wave in Water Using Acoustic Fiber Sensor", IEEE Trans. on Ultrasonics, Ferroelectrics and Frequency Control, Vol. 53, No. 4, pp. 761-767 (2006.4)
(27) T. Sakoda, Y. M. Sung and K. Matsukuma: " Plasma treatment on electrode surfaces of bifacial silicon solar cells", Solar Energy Materials & Solar Cells, Vol.90, No.7-8, pp.1089-1097 (2006.5)
(28) Tatsuya Sakoda, Toshiyuki Hamada, Kunihiro Matsukuma, Hiroki Herai, Kazuo Matsui and Kazuo Nagasawa: "Selective Etching of Silicon Nitride Film on Single Crystalline Silicon Solar Cell Using Intensive Surface Discharge", Jpn. J. Appl. Phys., Vol. 45, No. 5A, pp. 3992-3993 (2006. 5)
(29) Y. M. Sung, K. Ikeda, C. Honda and T. Sakoda: "Monitoring of an MgO Degradation in AC Plasma Display Panel Using Multivariate Analysis Method", Jpn. J. Appl. Phys., Vol. 45, No. 10B, pp. 8104-8108 (2006. 10)
*************************at University of Miyazaki *************************
(30) Tatsuya Sakoda and Yoshito Sonoda: "Visualization of sound field with uniform phase distribution using laser beam microphone coupled with computerized tomography method", Acoust. Sci. & Tech. Vol. 29, No. 4, pp. 295-299 (2008.4)
(31) D. Tashima, A. Sakamoto, M. Taniguchi, T. Sakoda and M. Otsubo: " Electrochemical Properties of Modified Carbon Electrode for Electric Double Layer Capacitor", Surface & Coating Technology, Vol. 202, No. 22-23, pp. 5560-5563 (2008.6)
(32) T. Hamada, T. Sakoda, M. Otsubo, K. Matsui and K. Nagasawa, "Optimization of Convex Electrode Geometry for Surface Discharge used for Fabrication of the Electrode Groove on Solar Cells", Surface & Coating Technology, Vol. 202, pp. 5405-5409 (2008.6)
(33) Masanori Takaoka, Tatsuya Sakoda, Masahisa Otsubo, Shigeru Akaiwa, Masatoshi Iki, Shigeharu Nakano: "Studies of Elastic Waves in Ethylene Propylene Rubber Using Acoustic Emission Sensor", IEEJ Trans. FM, Vol. 128, No. 10, pp.641-645 (2008.10)
(34) Tatsuya Sakoda, Yoshihisa Matsuda and Seiji Baba: "Development of Novel Ozonizer Using Micro-Barrier Discharges Formed in Water", Jpn. J. Appl. Phys., Vol. 47, No. 10, pp. 8030-8032 (2008. 10)
(35) D. Tashima, A. Sakamoto, M. Taniguchi, T. Sakoda, M. Otsubo, "Surface Modification of Carbon Electrode using Argon Plasma", Vacuum, Vol. 83, No. 3, pp. 695-698 (2008. 10).
(36) Kenich Haji, Yong Zhu, Masahisa Otsubo, and Tatsuya Sakoda, "Studies on Erosion of Silicone Rubber Exposed to Partial Arc Discharges", Polymer Degradation and Stability, Vol. 93, No. 12, pp. 2214-2221 (2008. 12)
(37) 濱田俊之, 荒川純一, 大坪昌久, 迫田達也: "高気圧沿面放電による太陽電池用電極溝の作製", 電学論A, Vol. 128-A, No.12, pp. 733-739 (2008.12)
(38) Toshiyuki Hamada, Tatsuya Sakoda, Masahisa Otsubo: "Plasma Grooving System Using Atmospheric Pressure Surface Discharge Plasma", Plasma Chemistry and Plasma Processing, Vol. 29, pp. 197-204, 2009 (2009.5)
(39) 枦健一, 椎原大輝, 荒田由浩, 迫田達也, 大坪昌久: "Dynamic Drop Testにおけるポリマー材料の撥水性低下に及ぼす水滴の帯電の影響", 電気学会論文誌A, Vol. 129, No. 5, pp. 386-387 (2009.5)
(40) Tatsuya Sakoda, Yoshihisa Matsuda, Seiji Baba: "Ozone Generation Using Micro Barrier Discharge in Water", J. Plasma Fusion Res. SERIES, Vol. 8, pp. 623-626 (2009.8)
(41) 椎原大輝, 荒田由浩, 枦健一, 三宅琢磨, 迫田達也, 大坪昌久: "Dynamic Drop Testにおける帯電及び塩分による試料表面の撥水性への影響", 電気学会論文誌A, Vol. 129, No. 9, pp. 657-663 (2009. 9)
(42) Tatsuya Sakoda: “Study on Behavior of Sputtered Particles during Surface Discharges” Jpn. J. Appl. Phys., Vol. 48, No. 10, pp. 106003-1-106003-4 (2009. 10)
(43) 枦健一, 平野公孝, 迫田達也, 大坪昌久: "局部アーク放電に曝されたシリコーンゴムの熱解析", 電気設備学会論文誌, Vol. 29, No. 10, pp. 865-870 (2009. 10)
(44) Kenich Haji, Kimitaka Hirano, Tatsuya Sakoda, Masahisa Otsubo: "Application of Thermal Analysis to Clarification of Degradation Characteristics of Silicone Rubber Exposed to Partial Arc Discharge", IEEJ (Institute of Electrical Engineers of Japan) Trans. on Electrical and Electronic Engineering, Vol. 4, No.6, pp.793-795 (2009.11)
(45) 迫田達也, 宮川祐一郎, 宮崎哲司, 大坪昌久, 生田昌輝, 鎗光隆義: “酸化亜鉛型避雷素子の筋状破壊機構の解明に関する研究”, 電気学会論文誌A, Vol. 129, No. 12, Sec. B, pp.1593-1594 (2009.12)
(46) Toshiyuki Hamada, Tatsuya Sakoda and Masahisa Otsubo: “Studies on Non-thermal Atmospheric Pressure Plasma Process Conditions for Groove Formation on Silicon Nitride for Silicon Solar Cells”, Materials Science in Semiconductor Processing, Vol. 12, No. 3, pp. 106-112 (2009. 12)
(47) Toshiyuki Hamada, Tatsuya Sakoda, Masahisa Otsubo: " Examination of Maskless Etching Technique Using a Localized Surface Discharge Plasma", IEEJ (Institute of Electrical Engineers of Japan) Transactions on Electrical and Electronic Engineering, Vol. 5, No. 1, pp. 115-117 (2010. 1)
(48) Tatsuya Sakoda, Toshihiko Nakashima, Masahisa Otsubo, Satoshi Kurihara, Shinya Nagasato, and Takayoshi Yarimitsu: “Diagnostics of Insulation Deterioration of Ethylene Propylene Rubber Using an Acoustic Emission Technique”, IEEE Transactions on Dielectrics and Electrical Insulation, Vol. 17, No. 4, pp.1242-1248 (2010. 8)
(49)濱田俊之, 水本貴之, 有村拓也, 迫田達也: "大気圧沿面放電プラズマを用いたマスクレスエッチング", 電気学会論文誌A, Vol. 130, No. 10, pp. 907-912 (2010.10 )
(50) Toshiyuki Hamada, Tatsuya Sakoda: "Etching Characteristics of Fabricated Grooves on Silicon Solar Cell Using Surface Discharge Plasma", Institute of Electrical Engineers of Japan Transactions on Electrical and Electronic Engineering, Vol. 130, No. 11, pp. 999-1003 (2010. 11)
(51) Takuya Yamamoto, Toshihiko Nakashima, Tatsuya Sakoda, Masahisa Otsubo, Satoshi Kurihara, Shinya Nagasato, Takayoshi Yarimitsu: "Studies on Acoustic Emission Signals Detected in an Oil-immersed Pole Transformer, Institute of Electrical Engineers of Japan Transactions on Electrical and Electronic Engineering, Vol. 130, No. 11, pp. 1031-1036 (2010. 11 )
(52)Tatsuya Sakoda, Mark Bowden: "Proposal of Multi-pass Laser Spectroscopic Technique for Diagnosing Atmospheric Pressure Discharge Plasmas", Institute of Electrical Engineers of Japan Transactions on Electrical and Electronic Engineering, Vol. 130, No. 11, pp. 1026-1030 (2010. 11)
(53) Daiki Shiibara, Yoshihiro Arata, Tatsuya Sakoda, Masahisa Otsubo, Tomikazu Anjiki: "Comparison of Degradation Phenomena on Silicone Rubbers Eroded by DC and AC Discharges", Vol. 130, No. 11, pp. 1009-1012 (2010. 11)
(54) Takuma Miyake, Yuya Seo, Tatsuya Sakoda, Masahisa Otsubo: "Relationship between Leakage Current and Pollution Deposits on the Surface of Polymeric Insulator", Vol. 130, No. 11, pp. 1009-1012 (2010. 11)
(55)Takuma Miyake, Yuya Seo, Tatsuya Sakoda, Masahisa Otsubo: "Assessing Long-term Reliability of Polymeric Housing Materials", Institute of Electrical Engineers of Japan Transactions on Power and Energy, Vol. 131, No. 6, pp. 530-531 (2011. 6)
(56)Yuya Seo, Norihito Oshikawa, Takuma Miyake, Tatsuya Sakoda, and Tomikazu Anjiki: "Characteristics of hydrophobicity loss on silicone rubber surface during a dynamic drop test with direct current voltage application", Nanoscale Research Letters, Vol. 7, Article ID4, pp.1-4 (2012. 1)
(57)Toshiyuki Hamada, Takuya Arimura, Tatsuya Sakoda: "Studies on optimal gas supply for a maskless etching system with micro- discharge plasma operated at atmospheric pressure", Plasma Chemistry and Plasma Processing, Vol. 32, No. 2, pp. 325-332 (2012. 3)
(58)有村拓也, 平野啓太, 濱田俊之, 迫田達也 :"沿面放電プラズマを用いたSiエッチングの電源周波数依存性", 電気学会論文誌A, Vol. 132, No. 4, pp. 333-334 (2012.4)
(59)Daisuke Tashima, Hiromu Yoshitama, Tatsuya Sakoda, Akihito Okazaki, Takayuki Kawaji :"Characteristics of powdered activated carbon treated with dielectric barrier discharge for electric double-layer capacitors", Electrochimica Acta, Vol. 77, pp. 198-203 (2012. 5)
(60) Takahiro Kato, Takuma Miyake, Daisuke Tashima, Tatsuya Sakoda, Masahisa Otsubo, Mitsuyuki Hombu:"Maximum Output Power Control using Short-Circuit Current and Open-Circuit Voltage of a Solar Panel", to be published in Jpn. J. Appl. Phys., Vol. 51, No. 10, 10NF08, pp. 10NF08-1-4 (2012. 10)
(61)本田一史, 押川 典仁, 三宅 琢磨, 迫田 達也, 吉田 ナオト, 古河 征二: “微細藻類がポリマーがいし外被材の絶縁特性に与える影響の評価”, 電気学会論文誌A, Vol. 132, No. 11, pp. 944-950 (2012. 11)
(62)三宅琢磨, 瀬尾裕也, 押川典仁, 迫田達也, 大坪昌久, 安食富和:"電気絶縁機器用ポリマー外被材の直流・交流時の電気的特性の評価, 電気設備学会誌, Vol. 32, No. 8, pp. 594-599 (2012.12)
(63)押川典仁, 徳永達也, 本田一史, 三宅琢磨, 迫田達也, 安食富和:"複合汚損試験によるシリコーンゴム表面上の放電開始時間の評価", 電気学会論文誌A, Vol. 133, No. 4, pp.205-210 (2013.4)
(64)塩満栄一, 有吉純也, 藤真介, 迫田達也, 貴島純次, 中島秀之:"通水型オゾナイザの放電形態が脱色特性に与える影響",
電気学会論文誌A, Vol. 133, No. 11, pp.606-607 (2013.11)
(65)塩満栄一, 迫田達也: "多孔質ガラス膜を用いた水中放電プラズマ発生装置の特性", 電気学会論文誌A, Vol.
134, No. 5, pp.321-326 (2014.05)
(66)北島純一, 迫田達也, 渡部清範:"クロスボンド接続を有するケーブルにおける部分放電位置標定法に関する基礎的検討",電気学会論文誌A,
Vol. 134, No. 6, pp.428-429 (2014.06)
(67)吉玉拓, 春田篤二, 田島大輔, 迫田達也:"電気二重層キャパシタの劣化要因に関する考察", Vol. 134, No. 10, pp.525-531 (2014.10)
(68)Masaru Tominaga, Toshiyuki Tanaka, Tatsuya Sakoda, Norikazu Mizoguchi,
Yoshiyuki Kushima:"Study on Plasma Sterilization of Plant Anthracnose
Pathogen in Water Mist", Information Engineering Express, International
Institute of Applied Informatics, Vol.1, No.4, pp. 11 – pp. 20 (2015.12)
(69)吉玉拓, 田島大輔, 迫田達也, 林則行, 湯原将光, 宇都宮隆: “化学分析による電気二重層キャパシタの劣化要因の考察”, 電気学会論文誌A, Vol.135, No.12, pp.792-798 (2015.12)
(70)濱田俊之, 峰大樹, 迫田 達也:"多孔質膜利用の水中アルゴンプラズマによる芽胞菌殺菌機構の考察", 電気学会論文誌A, Vol. 136, No. 1, pp.64-65 (2016.01)
(71) 井平学, 平島俊紀, 三宅琢磨, 迫田達也, 中野亮介, 鎌田文麿, 西昌美: “ 電力ケーブル接続部に有効な周波数加速劣化試験の基礎的検討”,
電気学会論文誌A, Vol. 136, No. 3, pp. 241-242 (2016. 3)
(72) 奥将俊,石津智子,田島大輔,迫田達也,林則行,穂高一条:"熱電発電システムにおける開放電圧を用いた最大出力点の探索法”,太陽エネルギー,
Vol. 42, No. 4, pp. 49-55 (2016. 4)
(73)富永大, 田中聡之, 迫田達也, 溝口則和, 櫛間義幸:"マンゴー炭疽病菌の分生胞子の殺菌に必要なオゾン濃度および処理時間に関する研究",
電気学会論文誌 A, Vol.136, No.11, pp.726-727(2016. 11)
(74)Hiroumu Yoshitama, Daisuke Tashima, Tatsuya Sakoda, Noriyuki Hayashi,
Masamitsu Yuhara, Takashi Utsunomiya :"Chemical Analysis of Casual
Elements for Deterioration of Cylindrical EDLC", Electronics and Communications
in Japan, Vol. 135-A, No. 12, pp. 792–798 (2016.12)
(75)Tatsuya Sakoda, Toshiki Hirashima, Tomoya Nakamura, Yugo Shirahama,
Noriyuki Hayashi: "Study on Grasping Partial Discharge Development
Using an Acoustic Emission Technique", The Journal of Cetral Power
Research Institute, Vol. 13, No. 1, pp. 13-17 (2017.3)
(76)Hibiki Horie, Tatsuya Sakoda, Katsutaka Kubo, Manabu Mizutani, Takato Fukano:"Improvement
of Discharge Ignition Characteristics of a Surge Arrester with a Spark
Gap", IEEJ Trans. PE, Vol. 137, No. 11, pp. 724-729 (2017. 11)
(77)奥将俊, 田島大輔, 迫田達也, 林則行, 穂高一条:"熱電発電システムにおいて各モジュール間の内部抵抗の違いを考慮した最大出力点追尾の制御手法", 太陽エネルギー, Vol. 44, No.1, pp. 79-87 (2018. 1)
(78)Cheikh Ibra Wade, Ryo Torihara, Tatsuya Sakoda and Noriyuki Hayashi:
"Numerical analysis of electrical characteristics of a PV module irradiated
by an impulse light flash", Journal of InternatIonal Council on Electrical
Engineering, Vol. 8, No. 1, pp. 8-13 (2018.2)
(79) 南英佑, 三宅琢磨, 迫田達也, 阿嘉良昌, 安食富和, 深野孝人:"ポリマー材料の撥水性と電気的特性の回復特性",
電気学会論文誌 A, Vol. 138, No. 3, pp. 115-116 (2018.3)
(80) Tatsuya Sakoda, Kosei Tabira, Takuma Miyake, Noriyuki Hayashi, Kenich
Haji, Yoshiaki Aka, Tomikazu Anjiki, Takato Fukano: "Discharge behavior
and dielectric performance of artificially polluted hydrophobic silicone
rubber", Journal of Electrostatics, Vol. 93, pp. 97-103 (2018. 4)
(81) 後藤 弘輝:"界面活性剤添加時の水中プラズマ源の特性", 電気学会論文誌 A, Vol. 138, No. 7, pp. 355-360 (2018.7)
(82)迫田達也, 堀江響, 武居周, 久保克隆, 水谷学, 深野孝人:” 配電用ギャップ付酸化亜鉛形避雷器の放電遅れ現象に関する研究, 電気学会論文誌A, Vol. 138, No. 9, pp. 457-462 (2018.9)
(83) Hiroki Goto and Tatsuya Sakoda:"Characteristics of underwater
plasma with surfactant", Electrical Engineering Japan, pp. 1-7, (Translated
Paper) DOI: 10.1002/eej.23165 (2018.10
(84) 土田潤一郎, 迫田達也, 田澤和俊, 市川博章, 溝口則和, 櫛間義幸: “誘電体バリア放電を用いたマンゴー軸腐病の発病抑制効果”,
電気学会論文誌A, Vol. 139, No. 5, pp. 279-280 (2019.5)
(85) 山下勝也, 三宅琢磨, 迫田 達也, 川野渉:”分岐線路における部分放電電流パルスの伝搬特性”, 電気学会論文誌A, Vol.140
No.2 pp.92-97 (2020. 2)
(86) 黒岩 拓真, 迫田 達也, 有元 慎太郎, 生田 昌輝:” 架橋ポリエチレンケーブルの防蟻層の遮水効果”, 電気設備学会論文誌, Vol.
40, No. 3, pp. 12-13 (2020.3)
(87) 山下勝也,三宅琢磨,迫田達也,川野渉, 宮川浩二:“ケーブルにおける 部分放電の位置標定技術”, 電気設備学会論文誌, Vol. 40
No. 4, pp. 14-19 (2020.4)
(88) Tatsuya Sakoda, Eisuke Minami, Takuma Miyake, Noriyuki Hayashi, Shigehiko
Goto, Yoshiaki Aka, Tomikazu Anjiki, Yasunori Kasuga, Takato Fukano:” Study on degradation diagnostic method for
silicone rubber”, Journal of Electrostatics, Vol. 107, pp. 103479-1-6(2020.6)
(89) Ryo TORHIHARA, Takafumi KODAMA, Osamu TAKENOUCHI, Tatsuya SAKODA, Noriyuki
HAYASHI:"Visualization and Diagnosis Method of Defective Photovoltaic
String Based on the Temporal Variation Characteristics of String Currents
in Generation Mode", Journal of Japan Solar Energy Society, Vol. 47,
No.3, pp. 1-10 (2021.9) (in Japanese)
(90) 中古賀雄太, 多田陽一朗, 迫田達也, 田澤和俊, 市川博章:"誘電体バリア放電によるマンゴーの軸腐病殺菌と殺菌要因の解明に関する研究",
電気学会論文誌A, Vol. 141, No. 6, pp. 385-390 (2021.6)
(91)足立昂平, 三宅琢磨, 迫田達也:"連続塩霧試験による経年シリコーンゴムの劣化評価", 電気学会論文誌 A(基礎・材料・共通部門誌),
Vol. 141, No. 10, pp. 590-596 (2021.10)
(92)森航, 迫田達也, 佐藤正春, 武井勝俊:” 油入変圧器内の部分放電による弾性波の効果的な測定方法の提案”, 電気学会論文誌A, Vol. 42, No. 3, pp. 124-125 (2022. 3)
(93)中口隆成, 迫田達也, 片岡達也, 岡本大, 立木潮, 二川和弘, 佐藤英章:” 誘導電流パルスによる水トリー起因の残留電荷の検出技術の開発”,
電気学会論文誌 A(基礎・材料・共通部門誌), Vol. 142, No. 7, pp. 345-346 (2022.7)
(94)Tatsuyta Sakoda, Katsutaka Kubo, Manabu Mizutani, Tomoki Chiba, Yasunori
Kasuga, Takato Fukano: “Influence of impulse corona discharge on discharge
time lag of a surge arrester with a spark gap”, Journal of Electrostatics,
Vol. 121, 10378 (2023.1)
(95)川口 哲平, 迫田 達也, 西村 豪志:”ボイド内電界強度および充填剤がエポキシ樹脂中電気トリーの進展特性に与える影響”, 電気学会論文誌
A(基礎・材料・共通部門誌), Vol. 143, No. 2, pp. 46-53 (2023. 2)
(96)May Thin Khaing, Kosei Yoshimura, Takuma Miyake, Tatsuya Sakoda, Uki
Kanenari, Yusuke Nishihiro:"Characteristics of Aged Silicone Rubber
Insulators Used in Outdoor for 20 Years ",IEEJ Transactions on Electrical
and Electronic Engineering, Vol. 19, No. 4, pp. 454-460 (2024.1)
(97)Khaing M.T., Miyake T., Sakoda T., Kanenari U., Nishihiro Y.:"Evaluation
of degradation degree of artificially degraded silicone rubber surface
by using surface discharge", Journal of Electrostatics, DOI:10.1016/j.elstat.2024.103898
(2024.3)
(98)Khaing M.T., Yoshimura K., Miyake T., Sakoda T., Goto S., Anjiki T.,
Chiba T., Kasuga Y.:"Short-time Fabrication of Degraded Surface on
Silicone Rubber Used for Insulators ",IEEE Transactions on Dielectrics
and Electrical Insulation, DOI:10.1109/TDEI.2023.3329789 (2024.4)
(99)Tin Zar Win Ko, Ryo Torihara, Tatsuya Sakoda, Noriyuki Hayashi:"Voltage
and Current Characteristics of Schottky Barrier Diodes and RectifierDiodes
Exposed to Standard Lightning Impulse Voltage", IEEJ Trans 2024, Vol.
19, pp. 1105–1112 (2024.6)
(100)渡部巧樹, 迫田達也, 高橋旭, 根岸直行, 宮崎和則:"誘導電圧パルスを用いた残留電荷検出による水トリー劣化ケーブル区間の標定技術",
電気学会論文誌A, Vol. 45, No. 1, pp. 23-29 (2045)
(1)迫田達也, 川上真, 宮尾貴幸, 内野喜一郎, 村岡 克紀:"磁気中性線放電プラズマの生成条件に関する研究", 九州大学大学院総合理工学研究科報告,第19巻 第3号, pp 323-329 (1997. 12)
(2)迫田達也, 贄田寛, 北原一太:"高周波放電プラズマを用いた不飽和脂肪酸への水素添加", 崇城大学研究報告,第25巻, 第1号, pp83-87 (2001.3)
(3)迫田達也, 前田定男, 内山直子, 古川勝彦:"プラズマを用いた低温度再生型活性炭の開発", 崇城大学研究報告, 第27巻, 第1号, pp31-35 (2002.3)
(4)迫田達也: "ゼロからの出発", 静電気学会誌, 第26巻, 第3巻, p140 (2002.3)
(5)迫田達也, 園田義人: "光回折効果による超音波の検出", 崇城大学研究報告, 第28巻, 第1号, pp95-99 (2003.3)
(6)迫田達也: " オゾン生成用誘電体バリア放電源の最適化に関する基礎研究", 崇城大学研究報告, 第29巻, 第1号, pp53-62 (2004.3)
(7)園田義人, 中園与一, 大内可人, 佐末崇史, 迫田達也: "レーザビームマイクロホンとコンピュータトモグラフィによる可聴音波分布の可視化", 九州東海大学工学部紀要, No. 32, pp.199-200 (2006.3)
(8)岡村健, 森本琢磨, 三宅琢磨, 迫田達也, 馬場誠二:"多孔質ガラス膜を用いたオゾナイザー開発に関する基礎研究", 宮崎大学工学部紀要, No. 36, pp.151-156 (2007.8)
(9)藤井太志, 平谷龍一, 辻利則, 金子正光, 竹之内修, 迫田達也, 大坪昌久, 本田親久, 甲斐稔康, 福元晋, 徳光明博, 安藤美利: "音響・電気信号ハイブリッド検出による運転中水車発電機の部分放電特性",宮崎大学工学部紀要, No. 36, pp.109-114 (2007.8)
(10)Yoshito Sonoda and Tatsuya Sakoda:"Measurement of Sound Field in Air Using Laser Beam Microphone Combined with Computerized Tomography", 九州東海大学工学部紀要, No. 34, pp.81-87(2008.3)
(11)園田義人, 白水かなみ, 迫田達也: "レーザビームマイクロホンCT法による2音源音場の可視化", 九州東海大学工学部紀要, No. 34, pp.95-96(2008.3)
(12)平谷龍一, 前田育也, 金子正光, 辻利則, 竹之内修, 大坪昌久, 本田親久, 迫田達也, 福元普, 徳満明博, 甲斐稔康, 安藤美利, "音響・電気的測定法を用いた運転中水車発電機の長期部分放電特性", 宮崎大学工学部紀要, No. 37, pp.163-168(2008.8)
(13)迫田達也: "大気圧プラズマを用いた太陽電池テクスチャとプラズマグルービング", 化学工業 (プラズマ技術の新しい挑戦, 特集), Vol. 61, No. 5, pp.349-354 (2010.5)
(14) 堀晃太郎, 麦谷翔平, 迫田達也, 林則行, 太良尾浩生: "低周波から中間周波における人体内部インピーダンス測定装置の開発", 宮崎大学工学部紀要, No. 44, pp. 27-31 (2015. 7)
(15)上栗伸仁, 田島大輔, 迫田達也, 林則行: "柚子を用いた電気二重層キャパシタ用炭素材料の開発", 宮崎大学工学部紀要, No. 44, pp. 9-12 (2015. 7)
(16)陣内雅人, 山下大地, 岩本丈, 三宅琢磨, 迫田達也: "シリコーン材料の劣化特性の評価", 宮崎大学工学部紀要, No. 44, pp. 33-40 (2015. 7)
(17)陣内雅人, 山下大地, 岩本丈, 三宅琢磨, 迫田達也: "触媒層の違いによる固体高分子形燃料電池用MEA の劣化特性",
宮崎大学工学部紀要, No. 44, pp. 41-47 (2015. 7)
(18)朝倉匡俊, 井平学, 三宅琢磨, 迫田達也, 壱岐祐典, 前田健作: “AE及び電磁波センサを用いた部分放電検出”,宮崎大学工学部紀要, No. 45, pp. 181-185 (2016)
(19)出口竜也, 枦健一, 三宅琢磨, 迫田達也, 阿嘉良昌, 安食富和, 深野孝人:”ポリマー材料の傾斜角度がポリマー表面の放電特性に与える影響”, 宮崎大学工学部紀要,No. 45, pp. 187-192 (2016)
(20)堂園大雅, 富永大, 迫田達也, 溝口則和, 櫛間義幸:” マンゴーに発生する病害にプラズマ処理が与える影響”, 宮崎大学工学部紀要,No. 45, pp. 193-198 (2016)
(21)平島俊紀,白浜優吾,中村友哉,三宅琢磨,迫田達也,緒方貴仁,鎌田文麿,副島通邦:"絶縁ゴムのトラッキング劣化過程におけるAE信号特性",
宮崎大学工学部紀要,No. 45, pp. 199-204 (2016)
(21)石川敏嗣,藤澤一平,迫田達也,林則之:"デシカント空調システムにおける外気の絶対湿度とシステム運転方式との関係",
宮崎大学工学部紀要,No. 46, pp. 179-184 (2017)
(22)堀江響, 迫田達也, 久保克隆, 水谷学, 深野孝人: "直列ギャップ付ZnO避雷器のV-t特性の改善に関する研究",
宮崎大学工学部紀要,No. 46, pp. 155-158 (2017)
(23)出口竜也, 迫田達也, 阿嘉義昌, 安食富和, 深野孝人: "交流課電によるポリマー材料の耐電圧特性評価", 宮崎大学工学部紀要,No. 46, pp. 159-163(2017. 7)
(24)白浜優吾,平島俊紀,中村友哉,迫田達也:"電磁波センサを用いた配電機器内部で生じる部分放電の検出", 宮崎大学工学部紀要,No. 46, pp. 139-142 (2017. 7)
(25)平島俊紀,中村友哉,白浜優吾,迫田達也:"絶縁体内部で発生する部分放電の劣化特性", 宮崎大学工学部紀要,No. 46, pp. 139-142(2017. 7)
(26)朝倉匡俊, 岸本恵修, 三宅琢磨, 迫田達也, 壱岐祐典, 前田健作:"真空遮断器を対象とした部分放電検知の劣化診断技術の開発", 宮崎大学工学部紀要,No. 46, pp. 133-138(2017. 7)
(27)西村豪志, 堂園大雅, 後藤弘輝, 富永大, 迫田達也:"マンゴーに発生する病害の防除を目指したプラズマミスと装置における芽胞菌及び大腸菌の殺菌", 宮崎大学工学部紀要,No. 46, pp. 175-178(2017. 7)
(28)春山浩, 杉下裕司,岡靖典,迫田達也:"配電設備の高経年化に対応した技術動向と課題調査", 電気学会論文誌B, Vol.139,
No.1, pp. 1-4 (2019.)
(29)池田佑允, 迫田達也, 佐藤英章, 春山浩, 宮崎和則:" :CVT ケーブルの劣化位置標定に関する基礎研究",
宮崎大学工学部紀要, No. 47, pp.143-148 (2018.7)
(30)川口翔大, 迫田達也, 阿嘉良昌, 安食富和, 深野孝人:" :塩分濃度を変化させた場合のポリマー材料の耐電圧評価",
宮崎大学工学部紀要, No. 47, pp. 149-152 (2018.7)
(31)川小根光輝, 白浜優吾, 中村友哉, 迫田達也:"変成器内部で生じる部分放電放射電磁波の周波数特性", 宮崎大学工学部紀要, No. 47, pp. 153-156 (2018.7)
(32)後藤弘輝, 西村豪志, 土田潤一郎, 迫田達也:" 界面活性剤添加時における水中プラズマ源の特性の検討", 宮崎大学工学部紀要,
No. 47, pp. 157-162 (2018.7)
(33)白浜優吾, 中村友哉, 川小根光輝, 迫田達也:" 配電機器内部で生じた部分放電による放射電磁波特性", 宮崎大学工学部紀要,
No. 47, pp. 163-166 (2018.7)
(34)田平耕成, 迫田達也, 阿嘉良昌, 安食富和, 深野孝人:" シリコーンゴムの塩害に対する耐汚損特性の検討", 宮崎大学工学部紀要,
No. 47, pp. 167-170 (2018.7)
(35)土田潤一郎, 西村豪志, 後藤弘輝, 迫田達也:" Heガスを利用したプラズマ装置における遷移発光強度の測定と芽胞菌の殺菌",
宮崎大学工学部紀要, No. 47, pp.171-174 (2018.7)
(36)中村友哉, 川小根光輝, 白浜優吾, 迫田達也:"プラグインエルボで発生する沿面放電特性", 宮崎大学工学部紀要,
No. 47, pp. 175-178 (2018.7)
(37)西村豪志, 土田潤一郎, 迫田達也:" 誘電体バリア放電を利用した殺菌装置における芽胞菌の殺菌", 宮崎大学工学部紀要, No. 47, pp. 179-182 (2018.7)
(38)南英佑, 迫田達也, 阿嘉良昌, 安食富和, 深野孝人:" 塩霧試験におけるポリマー材料の撥水性特性の評価", 宮崎大学工学部紀要,
No. 47, pp. 183-186 (2018.7)
(39)堀江響, 迫田達也, 久保克隆, 水谷学, 深野孝人:" 配電用直列ギャップ付酸化亜鉛形避雷器のV -t 特性の改善に関する研究",
宮崎大学工学部紀要, No. 47, pp. 187-192 (2018.7)
(40) Shunsuke KINOSHITA, Junichiro TSUCHIDA, Tatsuya SAKODA, Kazutoshi
TAZAWA, Hiroaki ICHIKAWA:”Sterilization of Stem-end rot of Mango using
a dielectric barrier discharge source”, MEMOIRS OF FACULTY OF ENGINEERING
UNIVERSITY OF MIYAZAKI, Vol. 48, pp.91-94 (2019.7)
(41)Junichiro TSUCHIDA, Shunsuke KINOSHITA, Tatsuya SAKODA:”Sterilization
of Bacillus Subtilis and measurement of O3 concentration in sterilization
device using dielectric barrier discharge”, MEMOIRS OF FACULTY OF ENGINEERING
UNIVERSITY OF MIYAZAKI, Vol. 48, pp.95-98 (2019.7)
(42)Katsuya YAMASHITA, Takuma MIYAKE, Tatsuya SAKODA, Wataru KAWANO:”Propagation
Characteristics of Partial Discharge Pulse Current on Branched Line”, MEMOIRS
OF FACULTY OF ENGINEERING UNIVERSITY OF MIYAZAKI, Vol. 48, pp. 99-102 (2019.7)
(43)Kyaw Myo Win, Yasuyuki Ota, Kensuke Nishioka, Tatsuya Sakoda, Noriyuki
Hayashi:"Multivariate Analysis Using R for Various Climatic Effets
on the Output Performances of CIGS and Multi-Crystalline Si Photovoltaic
Systems Installed in Miyazaki, Japan", Memoirs of Faculty of Engineering,
University of Miyazaki, No. 49, pp. 119-127 (2020.9)
(44) Katsuya YAMASHITA, Tatsuya SAKODA:”Study on Location Accuracy of Partial
Discharge Locator for Electric Power Cable”, Memoirs of Faculty of Engineering
University of Miyazaki, pp. 91-94 (2020.7)
(45) Katsuya YAMASHITA, Tatsuya SAKODA: “Study on Propagation Characteristics
of High Frequency Pulse Current in Electric Power Cable”, Memoirs of Faculty
of Engineering University of Miyazaki , pp. 95-100 (2020.7)
(46) Yuhei YAMASAKI, Katsuya YAMASHITA, Tatsuya SAKODA:”Partial Discharge
Characteristics of XLPE Cable with Water Tree”, Memoirs of Faculty of Engineering
University of Miyazaki , pp. 101-104 (2020.7)
(47) Hiroshi ODA, Tatsuya SAKODA, Takeru AISHIMA, Takeshi NISHIMURA:”Characteristics
of Partial Discharge in Epoxy Resin with a Void”, Memoirs of Faculty of
Engineering University of Miyazaki , pp. 105-110 (2020.7)
(48) Hiroshi ODA, Issei HAZAMA, Tatsuya SAKODA, Katsutaka KUBO, Manabu
MIZUTANI, Yasunori KASUGA, Takato FUKANO: “Affecting Factors to V-t Characteristics
of Impulse Discharge”, Memoirs of Faculty of Engineering University of
Miyazaki, pp. 111-114 (2020.7)
(49) Shunsuke KINOSHITA, Yoichiro TADA, Tatsuya SAKODA, Kazutoshi TAZAWA,
Hiroyuki ICHIKAWA: “Sterilization of Stem-end Rot of Mango using Dielectric
Barrier Discharge Source and Influence of Operating Gas on sterilization”,
Memoirs of Faculty of Engineering University of Miyazaki, pp. 115-118 (2020.7)
(50)Tin Tin Cho, Ryo Torihara, Tatsuya Sakoda, Noriyuki Hayashi:”Effect
of Supercapacitor on Transient Response of Thermoelectric Generation Systems”,
宮崎大学工学部紀要第51号, pp. 69- 77 (2022. 11)
1)M.Baba, T.Sakoda, T.Nakao, M.Otsubo, H.Nieda: "Gas Temperature Measurement in DC Glow and Impulse Glow-Arc Discharge by Multiplex CARS Method "Proceedings of the 8th International Symposium on High Voltage Engineering, Yokohama, Japan,(1993.8)
2)T.Sakoda, M.Otsubo, C.Otsubo, H.Nieda: "Gas Temperature and Cu vapor Measurements in and near an Impulse Discharge by Multiplex CARS and LIF Method", Proceedings of the 7th Asian Conference on Electrical Discharge, Xi'an, China,(1994.10)
3)T.Sakoda, M.Otsubo, C.Otsubo, H.Nieda: "Measurements of gas temperature and Cu vapor density in lighting impulse discharge using multiples CARS and laser induced fluorescence spectroscopy", 9th Gas Ninth international symposium on high voltage engineering. Graz, AUSTRIA, (1995.9)
4)T.Sakoda, M.Otsubo, C.Otsubo, H.Nieda: "Gas temperature and Cu Vapor Density in an impulse Discharge", 11th Gas Discharge Conference, Tokyo, Japan, (1995.9)
5)T.Sakoda, M.Bowden, K.Uchino, K.Muraoka, M.Maeda:”Thomson Scattering Studies of a Neutral Loop Discharge Plasma”, 7th International Symposium on Laser-Aided Plasma Diagnostics, Fukuoka, Japan, (1995.12)
6)T.Sakoda, M.D.Bowden, K.Uchino, K. Muraoka, M. Itoh, T. Uchida “Electron Density and Temperature in a Neutral Loop Discharge Plasma”, 49th Annual Gaseous Electronics Conference, Argonne, Illinois, USA, (1996.10)
7)T.Sakoda, T.Miyao, K.Uchino, K.Muraoka “Studies of a Neutral Loop Discharge Plasma Using Laser-Aided Diagnostics” Proceedings of the 8th International Symposium on Laser Aided-Plasma Diagnostics, p33-p38, Doorwerth, the Netherlands, (1997.9)
8)K.Uchino, T.Sakoda, K.Muraoka, M.Itoh, T.Uchida “Laser Scattering Diagnostics of a Magnetic Neutral Loop Discharge Plasma”, 50th Annual Gaseous Electronics Conference, p1750, Madison, Wisconsin, USA, (1997.10)
9)T.Sakoda, T.Arita, H.Nieda, K.Ando " Basic studies of acoustic emissions caused by the partial discharge in an oil tank", Proceedings of 1998 Korea and Japan Joint Symposium on Electrical Discharge and High Voltage Engineering, p16-19, Pusan, KOREA,(1998.10)
10)Y.M.Sung, K.Uchino, K.Muraoka, T.Sakoda "Studies on Electron Behavior in a Magnetic Neutral Loop Discharge Plasma", Proceedings of GEC 51/ICRP 4, p3-4, Hawaii, USA(1998.10)
11)T.Sakoda, T.Arita, H.Nieda, K.Ando " Characteristics of acoustic emissions caused by the partial discharge in an oil tank", The 9 th Asian Conference on Electrical Discharge, pA1-10, INDONESIA, (1998, 11)
(12)T.Sakoda, T.Arita, H.Nieda, K.Ando " Analysis of Acoustic Emissions Caused by the Partial Discharge in the Insulation Oil ", 13th International Conference on Dielectric Liquids, p483-486, Nara, JAPAN, (1999,7)
(13)T.Sakoda, T.Arita, H.Nieda, K.Ando, M.Otsubo, C.Honda, " Acoustic emissions caused by the corona discharge in an oil - tank ", 11 th International Symposium on High-Voltage Engineering (ISH 99) p164-167, London, ENGLAND, (1999.8)
14)Y.M.Sung, T.Sakoda, K.Uchino and K.Muraoka: "Studies on Electron Behavior in a Magnetic Neutral Loop Discharge Plasma", Proceedings of 1999 Japan and Korea Joint Symposium on Electrical Discharge and High Voltage Engineering,p137-140, Kitakyushu, JAPAN,(1999.10)
15)T.Sakoda, T.Arita, H.Nieda, K.Ando: " Diagnostic of Transformer Oil Based on Analyses of Acoustic Emissions", Proceedings of 1999 Japan and Korea Joint Symposium on Electrical Discharge and High Voltage Engineering, p121-124, Kitakyushu, JAPAN,(1999.10)
16)T.Sakoda, T.Matsune, H.Nieda and Y.Sonoda: " Measurements of Ultrasonic Waves using Laser Diffraction Method", Proceedings of 2000 Korea - Japan Joint Symposium on Electrical Discharge and High Voltage Engineering, p7051-7054, Ulsan, KOREA,(2000.10)
17)T.Sakoda, T.Matsune, T.Mochizuki, H.Nieda, S.T.Kim and K.Ando: "Observations of Acoustic Emissions due to a Corona Discharge in Oil-immersed Transformer ", The 10 th Asian Conference on Electrical Discharge, Kyoto, JAPAN, (2000.11)
18)T.Sakoda, S.Maeda, H.Nieda, S.Yamazaki, H.Ijiri, N.Uchiyama, K.Nishihara and K. Furukawa: "Surface treatment of activated carbon by using a radio - frequency CF4 plasma", 15th International Symposium on Plasma Chemistry, FRANCE, (2001. 7)
19)T.Sakoda, S.Maeda, N.Uchiyama and K.Furukawa: "Activated carbon modified by a radio frequency CF4 plasma", Proceedings of 2001 Japan-Korea Joint Symposium on Electrical Discharge and High Voltage Engineering, p205-208, Miyazaki, JAPAN,(2001.11)
20)T.Sakoda and Y.Sonoda:"Optical Fiber Sensor for Monitoring Electric Power Apparatuses", Proceedings of 2001 Japan-Korea Joint Symposium on Electrical Discharge and High Voltage Engineering, p13-16, Miyazaki, JAPAN,(2001.11)
21)T.Sakoda, T.Matsune, S.Maeda, K.Kitahara and K.Ando: "Characteristics of Hydrogen Plasma for Hydrogenation of Unsaturated Fatty Acid Esters", Proceedings of 2001 Japan-Korea Joint Symposium on Electrical Discharge and High Voltage Engineering,p201-204, Miyazaki, JAPAN,(2001.11)
22)M.Sakoda, T.Sakoda, S.Maeda and H.Nieda: "Studies on Ozone Generator of Silent Discharge Type without Spacer", Proceedings of 2001 Japan-Korea Joint Symposium on Electrical Discharge and High Voltage Engineering, p209-212, Miyazaki, JAPAN,(2001.11)
23)T. Sakoda, S. T. Kim and Y. Sonoda:"Detection of Low-frequency Ultrasonic Wave by Light Diffraction Technique", Proceedings of 2002 Joint Conference of ACED & K-J Symposium on ED and HVE, p50-53(2002.11)
24)T. Sakoda, A. Fukutomi, S. Maeda, N. Uchiyama, K. Imagawa, K. Nishihara and K. Furukawa:" Characteristics of Powdery Silica Gel Modified by Dielectric Barrier Discharge", Proceedings of 2002 Joint Conference of ACED & K-J Symposium on ED and HVE , p348-351(2002.11)
25)T. Sakoda, M. Sakoda, T. Matsune and S. Maeda :" Characteristics of Ozone Generation by Dielectric Barrier Discharge", Proceedings of 2002 Joint Conference of ACED & K-J Symposium on ED and HVE , p467-470(2002.11)
26) T. Sakoda and Y. Sonoda : "Development of optical acoustic sensor for monitoring of electric power apparatuses" , Proc. of the 13 th International Symposium on High-Voltage Engineering, p542 (2003.8)
27) T. Sakoda and Y. Sonoda : "Measurement of Low-Frequency Ultrasonic Wave by Acoustic Fiber Sensor", Proceedings of 2003 Japan-Korea Joint Symposium on Electrical Discharge and High Voltage Engineering, p93-96, Nagasaki, JAPAN (2003.11)
28) B. B. Saha, I. I. Ei-Sharkawy, S. Koyama, T. Ohara, K. Kuwahara, K. Furukawa and T. Sakoda: "Isothermal Adsorption and Thermophysical Property Measurements of Various Silica Gels and Copper Sputtered Type Silica Gel ", Proc. of the International Seminar on Thermally Powered Sorption Technology, p89-99, Fukuoka, JAPAN (2003.12)
29) T. Hamada, T. Sakoda, K. Matsukuma, H. Herai, K. Matsui and K. Nagasawa:" Studies of Condition Required for Formation of Electrode Grooves on Silicon Solar Cell Using Surface Discharge", 13th Asian Conference on Electrical Discharge, pp O14-1-O14-4, Sapporo, JAPAN (2006.10)
30) D. Tashima, A. Sakamoto, M. Taniguchi, T. Sakoda and M. Otsubo: "Surface Modification of Carbon Electrode using Argon Plasma", The 9th International Symposium on Sputtering & Plasma Process, p283-286, Kanazawa Japan (2007. 6)
31) S. Takagi, K. Ikeda, Y. Mizusako, T. Sakoda and C. Honda: "Measurement of Sputtered Mg Particles in an MgO Surface Discharge in AC-PDP", The 9th International Symposium on Sputtering & Plasma Process, p339-402, Kanazawa Japan (2007. 6)
32) T. Hamada, T. Sakoda, M. Otsubo, M. Matsui and K. Nagasawa: "Evaluation of Electrode Grooves Formed Using Surface Discharge Plasma", 18th International Symposium on Plasma Chemistry, CD-ROM 28P-74-1-4, Kyoto Japan (2007. 8)
33) M. Kurozumi, T. Sakoda and M. Otsubo : " Reduction of Harmonic Currents and Evaluation of Luminous Efficiency in a Lag Type Operating Circuit of a Metal Halide Lamp", 18th International Symposium on Plasma Chemistry, CD-ROM 30P-81-1-4, Kyoto Japan (2007. 8)
34) T. Sakoda, S. Takagi, Y. Tanaka and C. Honda : "Measurements of Sputtered Particles in Surface Discharge Using Laser Induced Fluorescence Technique", Laser Aided Plasma Diagnostics, p88-91, Gifu Japan (2007. 9)
(35) Keiich Haji, Yong Zhu, Masahisa Otsubo, Tatsuya Sakoda and Chikahisa Honda:" Relation between Dry Band Arc Discharge Development and Erosion Shape on the Silicon Rubber", 2007 Annual Report Conference on Electrical Insulation and Dielectric Phenomena, pp.312-315, Vancouver Canada (2007. 10)
36) K. Haji, D. Shiibara, Y. Yamashita, T. Miyake, T. Sakoda and M. Otsubo: " Dry Band Arc Discharge and its Predischarge on Silicon Rubber Specimens, 2007 Japan-Korea Joint Symposium on Electrical Discharge and High Voltage Engineering, pp. 231-234 (2007. 11)
37) M. Takaoka, T. Sakoda, M. Otsubo, K. Yoshimitsu and M. Iki: "Studies of Elastic Waves in Ethylene Propylene Rubber Using Acoustic Emission Sensor", 2007 Japan-Korea Joint Symposium on Electrical Discharge and High Voltage Engineering, pp. 15-18 (2007. 11)
38) Y. Miyakawa, T. Sakoda, M. Otsubo, T. Harada and K. Sakoda: "Studies on Understandings of Insulation Performance of ZnO Surge Arrester with Series Gap", 2007 Japan-Korea Joint Symposium on Electrical Discharge and High Voltage Engineering, pp. 311-314 (2007. 11)
39) J. Arakawa, T. Hamada, T. Sakoda and M. Otsubo: "Effects of Back Electrode for Etching of Silicon Nitride Film on Solar Cells Using Surface Discharge", 2007 Japan-Korea Joint Symposium on Electrical Discharge and High Voltage Engineering, pp.91-94 (2007. 11)
40) T. Tsuji, T. Kaneko, R. Hiratani, I. Maeda, C. Honda, M. Otsubo, T. Sakoda, O. Takenouchi, S. Fukumoto, A. Tokumitsu, T. Kai, M. Andou: "Characteristics of On-line Partial Discharge on Hydrogenerator Stator Windings by Hybrid Detection Method with AE sensors and CT sensor", 2007 Japan-Korea Joint Symposium on Electrical Discharge and High Voltage Engineering, pp. 23-26, (2007. 11)
41) T. Hamada, S. Arakawa, T. Sakoda and M. Otsubo: "Fabrication of Electrode Grooves on Silicon Solar Cells Using Surface Discharge", 17th International Photovoltaic Science and Engineering Conference, pp.708-709, (2007.12) Fukuoka, JAPAN
(42) I. Maeda, T. Kaneko, O. Takenouchi, T. Miyake, T. Sakoda, M. Otsubo, S. Fukumoto, A. Tokumitsu, T. Kai, M. Ando: "Characteristics of On-line and Off-line Partial Discharge for Hydorogenerator Stator Windings with AE Sensor and CT Sensor", Proceedings of 2008 International Symposium on Electrical Insulating Materials, pp. 577-580, (2008. 9)Mie, Japan
(43)Y. Miyakawa, T. Sokoda, M. Otsubo and M.Ikuta : "Influence of Temperature Variation on Characteristics of ZnO Elements", Proceedings of 2008 International Symposium on Electrical Insulating Materials, pp. 119-122, (2008. 9) Mie, Japan
(44)D. Shibara, K. Haji, T. Sakoda, M. Otsubo: "Fundamental Research on Characteristics of Hydrophobicity Disappearance of Silicone Rubber Surface in Dynamic Drop Test", Proceedings of 2008 International Symposium on Electrical Insulating Materials, pp. 99-102, (2008. 9) Mie, Japan
(45)Y. Yamashita, T. Miyake, H. Haji, T. Sakoda, M. Otsubo: "Relation Between Leakage Current and NSDD on the Surface of Polymer Insulator", Proceedings of 2008 International Symposium on Electrical Insulating Materials, pp. 103-106 (2008. 9) Mie, Japan
(46) Haji, Kenichi; Shiibara, Daiki; Otsubo, Masahisa, Sakoda Tatsuya, Yoshihiro Arata: "Characteristics Evaluation of the Partial Arc Discharge and the Silicone Rubber Surface by Dynamic Drop Test", 2008 Annual Report Conference on Electrical Insulation Dielectric Phenomena, pp. 272-275 (2008. 10) Canada
47) T. HAMADA, M. OTSUBO and T. SAKODA: "Etching of Silicon Nitride Using Atmospheric Pressure Surface Discharge Plasma", The 7th International Conference on Materials Processing for
Properties and Performance and The 3rd Asian Thermal Spray Conference, pp. AMFT-7005_1-3 (2008.11) Singapore
48) T. Hamada, T. Sakoda, and M. Otsubo :" STUDIES ON FORMATION OF ELECTRODE GROOVES FOR SOLAR CELL USING HIGH PRESSURE SURFACE DISCHARGE", Proceedings of the 4th International Congress on Cold Atmospheric Pressure Plasmas, pp. 33-36 (2009. 6) Gent, Belgium
49) T. Hamada, T. Sakoda, and M. Otsubo :" STUDIES ON ETCHINGS OF SILICON NITRIDE FILMS WITH VARIOUS FILM THICKNESS SILICON SUBSTRATES USING SURFACE DISCHARGE", Proceedings of the 4th International Congress on Cold Atmospheric Pressure Plasmas, pp. 37-40 (2009. 6) Gent, Belgium
50) T. Hamada, T. Sakoda, and M. Otsubo :" Studies on Si etching using atmospheric pressure surface discharge plasma", Proc. of The 10th International Symposium on Sputtering and Plasma Processes, pp.496-499 (2009.7), Kanazawa, Japan
51) Tatsuya Sakoda, Yoshihisa Matsuda, Yuji Tanaka, Seiji Baba, Junji Kijima, and Hideyuki Nakashima: “Studies on Discharge Mechanism of Micro-plasma Ozonizer Operated in Water”,
IOA 19th World Congress & Exhibition, pp. 12-1-1 - 12-1-4 (2009.8) Tokyo
Japan
52) T. Kaneko, T. Hidaka, T. Miyake, M. Otsubo, T. Sakoda, O. Takenouchi, M. Andou: "Characteristics of Distribution and Intensity for On-line Measurement Partial Discharge on Hydrogenerator Stator Windings using Acoustic Emission Sensors", 2009 Korea-Japan Joint Symposium on Electrical Discharge and High Voltage Engineering, pp. 87-90 (2009.11) Busan, Korea
53) Tatsuya Sakoda and Mark Bowden: “Proposal of Laser Raman Scattering Technique for Measurement of Molecular Density in Atmospheric Pressure Discharge”, 2009 Korea-Japan Joint Symposium on Electrical Discharge and High Voltage Engineering, pp. 230-233 (2009.11) Busan, Korea
54) T. Hamada, T. Sakoda, and M. Otsubo: “Studies on Etching Characteristics of Fabricated Grooves on Silicon Solar Cell Using Surface Discharge”, 2009 Korea-Japan Joint Symposium on Electrical Discharge and High Voltage Engineering, pp.234-237 (2009.11) Busan, Korea
55) M. Kurose, T. Yamamoto, T. Sakoda, and M. Otsubo: “Characteristics of Acoustic Emission Signals Detected in an Oil-immersed Pole Transformer”, 2009 Korea-Japan Joint Symposium on Electrical Discharge and High Voltage Engineering, pp. 310-313 (2009.11) Busan, Korea
56) K. Sakamoto, T. Nakashima, T. Sakoda, M. Otsubo, T. Yarimitsu, S. Nagasato, and S. Kurihara: “Location of Partial Discharge at Joint Section of CV Cable Using Acoustic Emission Technique”, 2009 Korea-Japan Joint Symposium on Electrical Discharge and High Voltage Engineering, pp. 314-317 (2009.11) Busan, Korea
57) S. Miyazaki, T. Sakoda, M. Otsubo, M. Ikuta, and T. Yarimitsu: “Investigation of Stripe-shaped Destruction Mechanism of ZnO Element”, 2009 Korea-Japan Joint Symposium on Electrical Discharge and High Voltage Engineering, pp.318-321 (2009.11) Busan, Korea
58) Takuya Arimura, Takayuki Mizumoto, Toshiyuki Hamada, and Tatsuya Sakoda: "Development of a grooving system for solar cell", 16 th International Conference on Electrical Engineering, CD-ROM (2010.7)Busan, Korea
59) Jannus M. N., T. Nakashima, T. Sakoda, M. Otsubo, S. Kurihara, S. Nagasato, T. Yarimitsu: "Location of Partial Discharge at Joint Section of XLPE Cable using Acoustic Emission Technique", 2010 Annual Report Conference on Electrical Insulation and Dielectric Phenomena, pp. 442-445 (2010. 10) Indiana, USA
60) J. M. Nainggolan, Toshihiko Nakashima, Tatsuya Sakoda, Masahisa Otsubo, Satoshi Kurihara, Shinya Nagasato: Investigation of Partial Discharge Location at Joint Section of XLPE Cable Using Acoustic Emission Technique, 15th Asian Conference on Electrical Discharge, pp. 30-33 (2010. 11) Xi'an, China
61) Takuma Miyake, Yuya Seo, Tatsuya Sakoda, Masahisa Otsubo, Tomikazu Anjiki: "Study on Insulation Degradation Difference between AC and DC Applications", 15th Asian Conference on Electrical Discharge, pp. 62-65 (2010. 11) Xi'an, China
62) S. Miyazaki, T. Sakoda, M. Otsubo, T. Miyake, H. Nakata, F. Kinoshita: "Characteristics of Deteriorated ZnO Elements with Stripe-shaped Destruction Trace", 15th Asian Conference on Electrical Discharge, pp. 74-77 (2010. 11) Xi'an, China
63)D. Tashima, R. Hirakawa, T. Sakoda and M. Otsubo, “Electrochemical Capacitances
of Carbon Powder Treated with Dielectric Barrier Discharge”, IEEE Conference
on Electrical Insulation And Dielectric Phenomena(Cancun, Mexico), No.2B-4,
pp.109-112 (2011.10) Mexico
64)T. Kato, T. Miyake, D. Tashima, T. Sakoda, M. Otsubo, M. Hombu, “Simulation of Maximum Output Power Control using Short-Circuit Current and Open-Circuit Voltage of a Solar Cell”, The 21st International Photovoltaic Science and Engineering Conference, No. 3D-6P-03 (2011.11) Fukuoka
65)Tatsuya Sakoda, Yuta Nakamura, Junichiro Kitajima, Masaki Sugiura, Satoshi Kurihara, Kenji Baba, Koichiro Kaneko, Takayoshi Yarimitsu, “Various Information Obtained from Acoustic Emissions Owing to Discharges in XLPE Cable”, World Academy of Science, Engineering and Technology, Vol. 69, pp. 1269-1274, 2012
66)Tatsuya Tokunaga, Shinnosuke Nishikawa,Tatsuya Sakoda, Takato Fukano: "Influence of triple-junction on sparkover voltage for a series gap of arrester", 2013 Electrical Insulation Conference, pp.110-113, (2013.6.2-5) Ottawa, Canada
67) Masaki Sugiura, Takuma Miyake, Tatsuya Sakoda, Yoichi Tsutagawa, Hidefumi Kawagoe, Masahiko guchi, Tomoyuki Nakagawa: "CHARACTERISTICS OF AE SIGNALS OBTAINED FROM FREQUENCY ACCELERATD DETERIORATION TEST WITH EP RUBBER', The 18th International Symposium on High Voltage Engineering, 891-895, (2013. 8.25-30) Seoul Korea
68) Tadamitsu Kaneko,Osamu, Takenouchi, Tatuya Sakoda, Noriyuki Hayashi: "Influence of Temperature on Characteristics of On-line Partial Discharge on Hydrogenerator Stator Windings using Acoustic Emission Measurement Method", The 18th International Symposium on High Voltage Engineering, pp.1964-1969, (2013. 8/25-30) Hanyang University in Seoul, Korea
69)H. Yoshitama, A. Haruta, D. Tashima, T. Sakoda, N. Hayashi: “Study on deterioration factors of an electric double-layer capacitor”, International Symposium on EcoTopia Science 2013 No. P-3-23, (2013.12/14), Nagoya, Japan
70)Masatoshi Oku, Daisuke Tashima, Tatsuya Sakoda, Noriyuki Hayashi : “Compensation
of output power characteristics of a partly-malfunctioned thermoelectric
generator system by using a diode bypass circuit”, Proceedings of International
Conference on Electrical Engineering 2014, No. SRP-1042, pp.384-389 (2014.6)
Jeju, Korea
71)T. SAKODA and T. MINE:"GAS-LIQUID INTERFACIAL DISCHARGE WITH A
POROUS GLASS MEMBRANE", Proceedings of the XXth International Conference
on Gas Discharges and their Applications, pp. 562-565, (2014.7.8), Orleans,
France
72)Masatoshi Oku, Noriyuki Hayashi, Tatsuya Sakoda, Daisuke Tashima: "Basic Characteristics of a Heat and Electricity Combined Generation System Using Biomass Fuel", 3rd The International Conference on Renewable Energy Research and Applications, pp. 222 - 227, (2014. 10/19-22), Milwakuee, USA
73)Manabu Ihira, Masatoshi Asakura, Takuma Miyake, Tatsuya Sakoda, Yusuke
Iki, Ryuya Kida: "Detection of Partial Discharge in Cubicle",
The 17th Asian Conference on Electrical Discharge, 31-1-31-4(2014.12/8
- 9), Thailand
74)Taiki Mine,Taiga Douzono, Tatuya Sakoda, Norikazu Mizoguchi: "Sterilization
Characteristics of Underwater Plasma", The 17th Asian Conference on
Electrical Discharge, 1-1-1-4(2014.12/8 - 9), Thailand
75)Masatoshi Oku, Noriyuki Hayashi, Tatsuya Sakoda, Daisuke
Tashima : “Basic Characteristics of a Heat and Electricity Combined Generation
System Using Biomass Fuel”, Proceedings of the 3rd International Conference on
Renewable Energy Research and Applications (ICRERA2014), ID:67, pp.222-228 (2014.10) Kyoto, Japan
76)Masatoshi Asakura, Manabu Ihira, Takuma Miyake, Tatsuya Sakoda, Yusuke
Iki, Ryuya Kida: “Detection of Partial Discharges for Vacuum Circuit Breaker
in Cubicle using Acoustic Emission and Electromagnetic Wave sensors”, The International Conference on Electrical Engineering, 15A-122-FP, 1-4(2015.
July 5-9) Hong Kong
77)Toshiki, Hirashima, Kenta, Miyabe, Tatsuya, Sakoda, Ryosuke, Nakano, Fumimaro, Kamada Masami, Nishi: “ Evaluation of Tracking Deterioration for a Plug in Elbow by an Acoustic Emission Technique”, The International Conference on Electrical Engineering, 15A-206-FP, 1-4(2015. July 5-9) Hong Kong
78)Toshitsugu Ishikawa, Masatoshi Oku, Daisuke Tashima, Tatsuya Sakoda, Noriyuki Hayashi: “Influence of Operation Modes of a Cooling Pump on Thermal and Electrical Properties of Thermoelectric Generator System”, The International Conference on Electrical Engineering, 15A-192-FP, 1-4, (2015. July 5-9) Hong Kong
79)Y. Aka, T. Fukano, Y. Kasuga, T. Anjiki and T. Sakoda: "Development of polymer housed surge arrester applied to D.C. railway systems", 2015 Asia-Pacific International Conference on Lightning (APL),) pp. 137-140 (2015.6) Nagoya
80)T. Sakoda and D. Tashima: "Observation of Creeping Flashover on
ZnO element", 2015 Asia-Pacific International Conference on Lightning
(APL), pp. 693-696 (2015.6) Nagoya
81)D. Yamashita, T. Miyake, T. Sakoda, Y. Aka, T. Anjiki, and T. Fukano: "Influence of Shed Inclination on Discharge Ignition under DC Voltage Application", 2015 Asia-Pacific International Conference on Lightning (APL), pp. 569-572 (2015.6) Nagoya
82) Masaru Tominaga , Toshiyuki Tanaka , Tatsuya Sakoda , Norikazu Mizoguchi
, Yoshiyuki Kushima : “Plasma Sterilization of Anthrax Pathogen in Water
Mist”, 2015 IIAI 4th International Congress on Advanced Applied Informatics,
pp. 690-694 (2015.7)Okayama
83)Tatsuya Sakoda, Daichi Yamashita, Tatsuya Deguchi, Takuma Miyake, Noriyuki
Hayashi, Kenich Haji, Yoshimasa Aka, Tomikazu Anjiki, and Takato Fukano:
“Characteristics of flashover on polluted polymer surface”, 2015 Korea-Japan
Joint Symposium on Electrical Discharge and HV Engineering, pp. 81-84 (2015.
11. 19) Mokpo, Korea
84)Masatoshi Asakura, Manabu Ihira, Takuma Miyake, Tatsuya Sakoda, Kensaku
Maeda, Yusuke Iki: “ Detection and Development of Partial Discharges for
Vacuum Circuit Breaker using Electromagnetic Wave Sensors”, 2015 Korea-Japan
Joint Symposium on Electrical Discharge and HV Engineering, pp.31-34, (2015.11.19-20)
Mokpo, Korea
85) Takeshi Nishimura, Masaru Tominaga, Junichiro Tsuchida, Tatsuya Sakoda,
Norikazu Mizoguchi, Yoshiyuki Kushima:" STERILIZATION OF COLLETOTRICHUM
SP. USING A DISCHARGE SOURCE", The First International Conference
on Hybridized Agriculture, pp. 40-46 (2016. 10. 21-24)
86)C. I. Wade, R. Torihara, Y. Fukamachi, T. Sakoda, N. Hayashi:"Numerical Analysis of I-V Characteristics and Siode Currents of a PV Module Reflected by Partial Shadow", 2016 IEEE Region 10 Conference (TENCON) — Proceedingsof the InternationalConference, pp. 2644-2647 (2016. 11) Singapore
87)Hibiki Horie, Takuma Miyake, Tatsuya Sakoda, Tatsuya Tokunaga, Katsutaka
Kubo, Manabu Mizutani, Takato Fukano:"Study on improvement of discharge
characteristics of a surge arrester with a spark gap", Joint Conference
of IWHV2016 & JK2016 on ED&HVE, pp. 81-85 (2016.11) Miyazaki
88)Yugo Shirahama, Toshiki Hirashima, Mitsuki Kawakone,
Takuma Miyake, Tatsuya Sakoda:” Detection of Partial Discharges in Electric
Power Equipment using an Electromagnetic Wave Sensor”, Joint Conference of
IWHV2016 & JK2016 on ED&HVE, pp. 51-54 (2016.11) Miyazaki
89)CHEIKH IBRA WADE, RYO
TORIHARA, TATSUYA SAKODA, NORIYUKI
HAYASHI:” Numerical Analysis of Electrical Characteristics of a PV Module
Irradiated by an Impulse Light Flash”, The International Conference on Electrical Engineering, 15A-192-FP, 1-4,ICEE 2017
90) K. M. Win, R. Torihara, S. Kita, T. Sakoda,
Y. Ota, K. Nishioka, N. Hayashi:” Long-Term Observation of Ambient Temperature
Effects on the Performance of A 60 kW
CIGS Solar Power System Installed in
Miyazaki”, 2018 IEEE Region 10 Conference
91) R. Torihara,
S. Kita, O. Takenouchi, T. Sakoda, Y. Ota, K. Nishioka, N. Hayashi:” Examination
of Compact and Online Diagnosis Method Based on Temporal Fluctuation of String
Currents of Photovoltaic Solar Plant”, 2018 IEEE Region 10 Conference
92)Thin Thin Hlaing, Tatsuya Sakoda, and Noriyuki Hayashi:" Control
of Voltage Rise Caused by the Reversed Power Flow in High Voltage Distribution
System by Detaching Shunt Capacitors and Optimum Location of PV Power Plant",
24th International Conference on Electrical Engineering, pp. 178-184 (2018.6)
Korea
93)Aung Ko Latt, Tatsuya Sakoda, and Noriyuki Hayashi:"Comarative
Analysis of Optimization Based Tuning Method and Conventional Tuning Method
for LFC of Multi-Area Power System", 24th International Conference
on Electrical Engineering, pp. 228-234 (2018.6) Korea
94)Kento Takezaki, Takuma Miyake, Tatsuya Sakoda,
Yoshiaki Aka, Tomikazu Anjiki, Takato Fukan:” Variation in Insulation
Performance of Artificially Polluted
Silicone Rubber”, 24th International Conference on Electrical
Engineering, pp. 1679-1684, (2018.) Seoul, Korea
95)Katsuya Yamashita, Souta Watanuki, Takuma Miyake, Tatsuya
Sakoda, Wataru Kawan:” Development of on-line partial discharge locator for electric power cable”, 2018 Electrical
Insulation Conference (EIC), pp. 216-219 (2018.6) San Antonio, TX, USA
98)Kyaw Myo Win, Ryo Torihara, Shohei Kita, Tetsuya Sakoda, Yasuyuki Ota,
Kensuke Nishioka, and Noriyuki Hayashi: "Long-Term Observation of
Ambient Temperature Effects on the Performance of A 60 kW CIGS Solar Power
System Installed in Miyazaki", Proceedings of TENCON 2018 - 2018 IEEE
Region 10 Conference (usb), No.1570461532、pp.1936-1941, (2018.10) Jeju,
Korea, 28-31 October 2018
99)Ryo Torihara, Shohei Kita, Osamu Takenouchi, Tetsuya Sakoda, and Noriyuki
Hayashi:"Examination of Compact and Online Diagnosis Method Based
on Temporal Fluctuation of String Currents of Photovoltaic Solar Plant",
Proceedings of TENCON 2018 - 2018 IEEE Region 10 Conference (usb), No.1570461493,
pp.1931-1935 (2018.10) Jeju, Korea, 28-31 October 2018.
100)Tatsuya Sakoda, Mitsuki Kawakone, Noriyuki Hayshi, Makoto Setoguchi,
Makoto Setoguchi:”Material Temperature Dependence on Behavior of Partial
Discharge in Epoxy Resin”, pp. 205-208, 2019 Electrical Insulation Conference
(EIC), Calgary, Alberta, Canada, 16-19 June 2019
101)Katsuya Yamashita, Takuma Miyake, Tatsuya Sakoda, Wataru Kawano:”Study
on Location Accuracy of Partial Discharge Locator”, pp.321-324, 2019 Electrical
Insulation Conference (EIC), Calgary, Alberta, Canada, 16-19 June 2019
102)TAKEZAKI Kento, MIYAKE Takuma, SAKODA Tatsuya, GOTO Shigehiko, AKA
Yoshiaki, and ANJIKI Tomikazu: “Electrical characteristics of artificially
polluted silicone rubber”, The International Council on Electrical Engineering
(ICEE) Conference, ICEE 19J-206 (2019. 7) Hong Kong
103) Tatsuya Sakoda, Noriyuki Hayashi, Yuhei Yamasaki, Soichiro Nakanose,
Takuma Miyake, Wataru Kawano, Koji Miyagawa: “On-line PD system and PD
Locator for XLPE Cables”, 8th International Conference on Condition Monitoring
and Diagnosis (CMD 2020), Paper ID:500, pp. 1-4 (2020. 10.25-28) Phuket,
Thailand
104) Torihara R., Kita S., Takenouchi O, Sakoda T., Hayashi N.:"Influence
of defective bypass diodes on electrical and thermal properties of photovoltaic
string and array", IEEE Region 10 Annual International Conference
Procedings, pp. 1007-1012 (2020.11)
105)Swezin Linnhtet, MayOo Khin, Ryo Torihara, Tatsuya Sakoda, Noriyuki
Hayashi:” Change in V-I Characteristics of Schottky Barrier Diodes when
Application of Standard Lightning Impulse Voltage Causes Breakdown of Them”,
The International Council on Electrical Engineering Conference 2022, pp.
635-641 (2022, June)
106)Tinzar Winko, MayOo Khin, Ryo Torihara, Tatsuya Sakoda, Noriyuki Hayashi:”
Voltage and Current Characteristics of Schottky Barrier Diodes when Application
of Standard Lightning Impulse Voltage Causes Breakdown of Them”, The International
Council on Electrical Engineering Conference 2022, pp. 642-649 (2022, June)
107)May Thin Khaing, Kosei Yoshimura, Tatsuya Sakoda, Junki Oasa, Shoichi
Higashiyama, and Yuko Inaoka:”Degradation Monitoring of Silicone Rubber
Used for Insulators”, P1-31, pp. 382-386, 9th International Conference
on Condition Monitoring and Diagnosis 2022 (2022.11)
108)May Thin Khaing, Kosei Yoshimura, Tatsuya Sakoda, Shigehikok Goto, Tomikazu
Anjiki, Tomoki Chiba, Yasunori Kasuga:"Formation of Degradation Layer
on Silicone Rubber Used for Insulators", 2023 Electrical Insulation
Conference (EIC), pp, 209-212 (2023. 6) Quebec, Canada
109)May Thin Khaing, Kosei Yoshimura, Tatsuya Sakoda, Shigehiko Goto, Tomikazu
Anjiki, Tomoki Chiba, Yasunori Kasuga:"Short-time Evaluation Technique
of Degradation Degree by Surface Discharge", International Symposium
on High Voltage Engineering, pp. 866-870 (2023.8) UK, Glasgow
110)Swe Zin Linn Htet, Takuya Konda, May Thin Khaing, Tatsuya Sakoda, Yoshihiro
Harada, katsutoshi Takei, Masaru Ikeda, Kazunori Miyazaki: "Partial
Discharge and Electrical Treeing Phenomena within Two Spherical Voids in
Epoxy Resin", 2024 10th International Conference on Condition Monitoring
and Diagnosis (CMD), pp. 358-361 (2024.10), Gangneung, Korea
111)May Thin Khaing, Takuma Miyake, Tatsuya Sakoda, Shigehiko Goto, Tomikazu
Anjiki, Tomoki Chiba, Yasunori Kasuga:"Diagnosis of Degradation Degree
on SiR SurfaceUsed for Insulator by Surface Discharge"2024 10th International
Conference on Condition Monitoring and Diagnosis (CMD), pp. 386-389